Skip to content
  • There are no suggestions because the search field is empty.

How to Install a ProofVision Bathroom TV

This guide explains the basic installation process for ProofVision WebOS Smart Bathroom TVs, including preparing the recess, installing the mounting plate, connecting the TV, testing it and sealing the finished installation. Important: Installation should be completed by a technically competent person. If you are unsure about any part of the installation, contact a qualified electrician or AV professional.

Before installing a ProofVision bathroom TV:

  • Check that all supplied accessories are present:
    • TV 
    • Metal back-mounting plate (this will be mounted to the back of the TV)
    • Screws and fixings for the back-mounting plate. 
    • 12v Power Supply + UK mains lead
    • Splashproof remote control + CR2032 battery
    • Non-waterproof LG-style magic remote control + 2 x AA batteries
  • Confirm the correct TV size and mounting plate dimensions.
  • Check that the installation wall is flat and level.
  • Decide on the viewing position.
  • Check for pipes, cables and other hazards before creating the recess.
  • Plan the required cables and connections.
  • Test the TV before completing the installation.

ProofVision bathroom TVs are designed to be recessed into the wall and sealed to the surrounding wall using bathroom-grade silicone.

TV & Mounting Plate Dimensions

TV Size Front Glass Screen Mounting Plate / Recess Dimensions
19" 490 × 335 × 5 mm 473 × 318 × 51 mm
24" 594 × 396 × 5 mm 577 × 379 × 51 mm
27" 658 × 454 × 5 mm 642 × 438 × 54 mm
32" 775 × 508 × 5 mm 760 × 492 × 57 mm
43" 1031 × 661 × 5 mm 1006 × 635 × 61 mm

NOTE: We recommend that you always check the installation instructions supplied with your specific TV before preparing the recess.

Installation Steps

Stage 1 - First-Fix

Prepare the recess + cabling

Create a suitable wall recess based on the mounting plate dimensions. The wall must be flat and level as the TV will sit in the mounting plate using magnets.

Run the supplied power lead and transformer to a suitable power connection point in accordance with local electrical regulations.

It is also advised at this point to arrange any other cabling such as a network cable (CAT5e/CAT6) , HDMI or an aerial feed. These cables should approach the recess from the bottom to match the cable entry point on the TV. 

Install the mounting plate

Insert the mounting plate into the recess so that the front metal flange sits flush with the finished tile surface. Secure the supplied mounting plate to the surrounding structure using the screws included and check that it is level.

Networking

If smart features are required, it is important to consider the method of connectivity to the internet and how it will affect streaming quality or access to various smart features.

Using a hard-wired internet connection will ensure a stable user experience with the TV's smart features. 

If using Wi-Fi, consider the following :

  • Distance from the wireless router or access point.
  •  Construction materials between the TV and router. Stone or masonry walls can reduce wireless signal strength. 

Designer (3)

Stage 2 - Mounting the TV

Connecting the Cables

Remove the rear input cover plate by undoing the retaining screws to expose the connections area and connect the required power and any HDMI / CAT6 / aerial or satellite or any other cables chosen for your installation.

Ensure cables are loose enough that they will not be pulled out from their inputs after mounting due to tension.

Mount the TV

Carefully lower the TV into the mounting plate. The integrated magnets will hold the unit securely in position when correctly seated and the metal edge behind the glass will be resting on the tiles around all 4 edges.

Caution: The TV front is made from glass - excessive force can cause damage

If the TV does not sit correctly within the housing, check the recess, mounting plate and cable routing.

Pre-Seal Test

We recommend testing the below functions before carrying out the sealing:

  1. Check that the TV is level and evenly seated against all four sides of the mounting plate before applying silicone
  2. That the TV turns on from standby using both remote controls.
  3. After being turned on, the display operates correctly and there are no visible screen defects, lines or pixel abnormalities.
  4. The TV is connecting to the internet during the initial setup screens
  5. Any connected inputs are working as intended
  6. Play content with sound to check that the audio is clear (Some vibration or resonation may be noticeable before sealing due to the installation not yet being complete. This should reduce once the TV has been fully sealed into the wall.)

Stage 3 - Sealing the TV

ProofVision TVs require sealant to be applied so no water can reach behind the screen.

Apply a continuous bead of neutral-cure bathroom-grade sanitary silicone around all four edges of the TV and Smooth the sealant to ensure full contact between the TV glass and surrounding wall finish.

Final Inspection

After sealing:
•    Verify there are no gaps in the silicone seal.
•    Remove excess sealant.
•    Confirm the TV remains level and fully seated.
•    Allow the sealant to cure in accordance with the sealant manufacturer's instructions before exposing the area to moisture.

Common Installation Questions

Does the TV need to be recessed?

Yes. ProofVision bathroom TVs are designed for recessed in-wall installation and are not suitable for surface-mounted installation.

Does the TV need to be sealed?

Yes. ProofVision bathroom TVs are designed to be sealed into the wall using silicone. Failure to fully seal all four edges of the TV may allow moisture to reach the installation cavity and could lead to damage.

Can I remove the TV after it has been sealed?

Yes. The TV can be removed for maintenance by carefully cutting and removing the silicone seal around the perimeter before lifting the TV from the mounting plate.

What if the TV doesn't sit correctly?

Do not force it. Check that the wall is flat, the mounting plate is correctly installed and no cables are obstructing the TV.

Where should the transformer go?

The transformer and mains connection should be installed in a suitable accessible location in accordance with applicable electrical regulations. The transformer should not interfere with the TV seating correctly within the mounting plate.

Should I test the TV before installation?

Yes. We recommend testing the TV, internet connection, aerial/satellite feed, HDMI inputs and audio operation before sealing the TV into the wall.

Installation Checklist

☐ Wall/recess prepared

☐ Mounting plate securely fixed and level

☐ Required cables connected

☐ Power supply connected and tested

☐ Screen, audio and connections tested

☐ Wi-Fi/Ethernet tested

☐ TV level and correctly mounted

☐ Silicone applied around all four edges

☐ Seal checked for gaps

☐ TV operating correctly after sealing